Back to Insights

Roll-out shelving for long items

Heavy-duty electric telescopic cantilever rack with extended drawers for industrial steel storage

Stop sacrificing your high-purity stainless steel tube surface finishes to forklift damage. For Steel Service Centers and sanitary component manufacturers, preserving the Ra value of your inventory is as critical as the storage space itself. Our Roll-out shelving for long items eliminates side-loading risks, allowing direct overhead crane access for 304/316L tubes, polished bars, and heavy structural profiles.

Preserving Surface Integrity: The “No-Friction” Storage Logic

In the world of hygienic stainless steel components—whether for dairy, pharmaceutical, or semiconductor applications—a scratch is not just a cosmetic defect; it’s a bacterial trap. Traditional static cantilever racks force you to use forklifts. The inherent problem with forklifts in this specific sector is the horizontal entry. To retrieve a bundle of polished tubes from a middle shelf, the operator must maneuver forks into a tight pocket, often scraping adjacent bundles or the rack arms themselves.

De Telescopic Cantilever Rack changes the physics of retrieval. By allowing the entire storage level to crank out 100% into the aisle, we convert the operation from a horizontal “dig” to a vertical “lift.”

Red heavy-duty cantilever rack in a warehouse with overhead crane accessing metal profiles

Figure 1: Overhead crane accessible racking allows for vertical lifting using nylon slings, completely eliminating metal-on-metal contact during retrieval.

The Role of Overhead Cranes in Sanitary Steel Handling

As shown above, integrating an rolbruggen (or bridge crane) with your storage system is the gold standard for handling high-value metals. Once the drawer is extended, your operator can lower nylon straps or a vacuum lifter directly onto the specific bundle of tubing or bar stock. There is no dragging, no sliding, and no “fishing” for material. This capability is essential for maintaining the strict surface roughness standards (e.g., 20 µin Ra) required by ASME BPE or 3-A Sanitary Standards.

Eliminating the “Wait Time” at the Laser & Saw

For a high-volume processing center, the most expensive cost isn’t the storage—it’s the idle time of your cutting equipment. If your laser cutter or band saw is waiting 20 minutes for a forklift driver to unbury a specific heat number of 316L bar stock from the bottom of a stack, you are bleeding profitability.

Onze telescoopgiek systems facilitate a “Selectivity First” approach. Every level is accessible independently. An operator can retrieve a single piece of heavy wall pipe or a full bundle in under 3 minutes.

Operator using a manual crank handle to extend a roll-out cantilever shelf level

Figure 2: Manual crank mechanisms feature high-ratio gearing, allowing a single operator to move thousands of pounds of steel bar stock with minimal effort.

This efficiency gain allows for Just-In-Time (JIT) feeding of your CNC machines and saws, significantly reducing the WIP (Work In Progress) clutter on your shop floor.

Get A Quote For Your Facility

Technical Specifications: Built for Heavy Metal

Whether you are storing heavy wall stainless pipes or solid bar stock, the structural integrity of the rack is non-negotiable. Unlike light-duty shelving, our systems are engineered with structural steel components designed to withstand the dynamic loads of cranking and the static loads of dense metal storage.

Electric telescopic cantilever storage system with operator using remote control

Figure 3: For high-frequency environments, electric drive systems allow operators to extend drawers via remote control, further improving ergonomics and speed.

Functie Specification / Benefit
Extension Capacity 100% Full Extension (Clear access for overhead cranes)
Load Capacity Per Arm/Level Up to 6,600 lbs (3,000 kg) per level standard; customizable for heavier loads.
Material Lengths Accommodates 20ft, 24ft, or custom lengths for tubing and profiles.
Drive Mechanism Manual Crank (low maintenance) or Electric Motor (high throughput).
Surface Protection Optional UHMW (ultra-high molecular weight polyethylene) liners on arms to prevent stainless steel contamination.

Optimizing Floor Space for High-Value Inventory

In a Steel Service Center, square footage is directly tied to revenue. Traditional layouts require massive aisles—often 12 to 15 feet wide—to allow forklifts to turn with long loads. By switching to overhead crane accessible racking, you can slash aisle widths down to the size of a walking path (approx. 4-5 feet). This consolidation allows you to store 50-80% more inventory in the same footprint, or free up floor space for additional processing equipment like tube benders or polishing stations.

Side view of double-sided extendable cantilever rack with drawers pulled out

Figure 4: Double-sided configurations maximize density, allowing centralized storage that feeds multiple workstations simultaneously.


Veelgestelde vragen (FAQ)

Q1: Can we use this system for polished stainless steel tubes without scratching them?
A: Yes. This is the primary advantage of the system. Because the arms extend 100%, you use an overhead crane with nylon slings to lift the bundle straight up. There is no sliding friction or contact with the arms during retrieval, preserving the Ra surface finish.

Q2: What is the maximum length of bar stock we can store?
A: Our racks are modular. While standard models fit 20ft (6m) lengths common in the steel industry, we can configure the number of columns to support 40ft or longer extrusions and profiles without sagging.

Q3: Does the rack require special floor preparation?
A: Due to the high density of steel storage (often exceeding 20,000 lbs per unit footprint), a standard 6-inch reinforced concrete slab is usually required. We provide specific point load data to your engineers to verify floor capacity before installation.

Q4: Can we store mixed inventory (e.g., tubes and small fittings) on the same rack?
A: Yes. We can accessorize the cantilever arms with steel pans or dividers. This allows you to store long tubes on lower levels and pallets of fittings, valves, or clamps on upper levels, keeping all related SKUs in one zone.

Q5: How does this compare to a honeycomb (pigeonhole) rack?
A: Honeycomb racks are notorious for damaging material surfaces during insertion/extraction and are difficult to inventory count. Roll-out shelving provides full visual access for cycle counts and eliminates the “drag and scrape” damage inherent in pigeonhole storage.

Need a Custom Storage Solution?

Speak directly with our technical engineers. We offer free structural designs, heavy-duty catalog evaluations, and quick B2B price quotations.

Request a Quote Now →